Comparing an induction cooktop with an electric coil range comes down to one ratio: how much of the electricity drawn at the wall ends up in the pan. Department of Energy test data puts electric coil efficiency at 73.7 percent and induction at 84.0 percent, so the same cooking task needs 1.19 units of input energy on induction against 1.36 units on a coil. Converting that ratio into an annual bill takes three more inputs: the average draw while cooking, the hours cooked each week, and the local price per kilowatt-hour.

Efficiency Values and What They Actually Measure

The DOE procedure heats an aluminum test block from room temperature to 144 degrees Fahrenheit above ambient at full power, then holds 25 percent power for fifteen minutes and measures the heat delivered. Under that procedure, coil elements measured 71.9 percent and induction elements measured between 70.7 and 73.6 percent in direct laboratory work. The widely quoted 84 percent induction figure was not measured by DOE laboratories but referenced from an external study, and manufacturer testing tends to place real induction efficiency between 74 and 81 percent.

This matters for any calculation that promises a large saving. The 84 percent figure is used here because it appears in the DOE-derived comparison tables that appliance analysts rely on, but the number should be treated as an upper bound rather than a measurement of a specific cooktop. At 84 percent, induction needs 12.3 percent less input electricity than a coil for identical heat delivered. At 77 percent, the gap narrows to about 4 percent, and the annual difference shrinks with it.

Setting the Weekly Cooking Profile

Rated wattage describes the maximum draw of one zone, not the energy used in a session. A portable single-zone induction unit draws 1200 to 1800 watts, while a built-in four-zone cooktop totals 7000 to 11000 watts across all zones, with individual zones at 1800 to 3700 watts on boost. A household never runs every zone at maximum for the whole session, so the calculation needs an average draw rather than a nameplate figure.

The profile used here is six hours of active cooking per week at an average draw of 1.5 kilowatts, which gives 9.0 kilowatt-hours of input electricity on a coil. That is a mid-range assumption for a household cooking most evenings, and it is deliberately stated as an assumption: a household that cooks twice a day, or one that mostly reheats, will land somewhere else. Six hours at 1.5 kilowatts is the reference point for every figure that follows.

From Delivered Heat to Input Kilowatt-Hours

The coil consumes 9.0 kilowatt-hours at the wall, and at 73.7 percent efficiency it delivers 6.63 kilowatt-hours of heat to the cookware. The induction cooktop has to deliver the same 6.63 kilowatt-hours to do the same cooking. Dividing by 84 percent gives 7.89 kilowatt-hours of input, which is the number that appears on the meter.

The difference is 1.11 kilowatt-hours per week, or 12.3 percent of the coil figure. Over 52 weeks the coil draws 468 kilowatt-hours and the induction cooktop draws 410 kilowatt-hours. Compared with the standby load of a refrigerator or the duty cycle of a water heater, both are small numbers: cooking is a minor slice of household electricity, and the comparison is between two modest quantities rather than between a large one and a small one.

Applying the Residential Price

The US average residential price was 16.48 cents per kilowatt-hour in 2024 and 17.23 cents in 2025, according to the Energy Information Administration. The Department of Energy representative average unit cost for 2025, used for appliance test procedures and EnergyGuide labeling, is 17.22 cents per kilowatt-hour. That figure is the one applied here, and local tariffs should be substituted where they differ.

At 17.22 cents, the coil profile costs 80.59 dollars a year and the induction profile costs 70.71 dollars, a difference of 9.88 dollars. Doubling the cooking time to twelve hours a week doubles both figures and doubles the gap to about 19.76 dollars. Halving it halves the gap again. The saving scales linearly with hours cooked, which makes the household schedule the dominant variable, not the cooktop.

Standby Draw and the Payback Question

Touch controls and pan sensors draw roughly 1 to 3 watts continuously. At 2 watts, that is 17.52 kilowatt-hours a year, or 3.02 dollars at 17.22 cents. Both induction and electronic coil cooktops carry this load, and mechanical coil models with knob controls carry none, so standby affects the total bill without changing the difference between the two technologies by much.

The payback calculation is where the efficiency gap loses its persuasive force. An induction cooktop typically costs more than a comparable coil model; taking a 400 dollar premium as an example, and a 9.88 dollar annual saving, the simple payback is about 40 years. A household cooking twelve hours a week saves 19.76 dollars and shortens the payback to about 20 years. Neither figure supports a purchase justified on energy alone. The case for induction rests on faster response, finer control at low heat, a cooler kitchen in summer, and the absence of combustion products indoors.

Calculation Checklist

Average draw: the kilowatt figure read while the zone is actually cooking, not the nameplate maximum.

Weekly hours: active cooking time across all zones, recorded for a typical week.

Weekly input energy: average draw in kilowatts multiplied by hours.

Delivered heat: weekly input energy multiplied by 0.737 for a coil or 0.840 for induction.

Comparable input: delivered heat divided by the efficiency of the other technology.

Annual energy: weekly input energy multiplied by 52.

Annual cost: annual kilowatt-hours multiplied by the local residential rate.

Standby: continuous draw in watts multiplied by 8.76 to get annual kilowatt-hours, then priced at the same rate.

Payback: equipment price premium divided by the annual saving, with the result read as a rough screen rather than a forecast.